The relative strength index (RSI) compresses recent price changes into a single number between 0 and 100. You will see how it is calculated with Wilder smoothing, how to work out a value by hand, and why a high reading is not a sell signal on its own.
What RSI measures
RSI compares the size of recent up-moves with the size of recent down-moves. Each candle, the change in close from the previous candle is split into a gain (if positive) or a loss (if negative, stored as a positive number). The indicator then looks at the average gain and the average loss over N candles.
If gains dominate, RSI is high. If losses dominate, it is low. If both are equal, RSI is 50. A period of 14 is a common example, but it is only a convention.
The calculation with Wilder smoothing
RSI exists in several variants. This lesson uses Wilder smoothing, the original method, which is also what the QuantRaider RSI node states it uses. Instead of a plain average, the average gain and average loss are updated each candle with a running rule, which is similar to an EMA with α = 1 / N.
Average gain now = (Average gain previous × (N − 1) + Gain now) / N
Average loss now = (Average loss previous × (N − 1) + Loss now) / N
RS = Average gain / Average loss
RSI = 100 − 100 / (1 + RS)Worked example
One RSI value from average gain and average loss
- Take N = 14 with an average gain of 0.60 and an average loss of 0.40 (in price points).
- RS = 0.60 / 0.40 = 1.5, so RSI = 100 − 100 / (1 + 1.5) = 100 − 40 = 60.
- The next candle closes up by 1.00, so the gain is 1.00 and the loss is 0.
- New average gain = (0.60 × 13 + 1.00) / 14 = 8.80 / 14 = 0.6286. New average loss = (0.40 × 13 + 0) / 14 = 5.20 / 14 = 0.3714.
- RS = 8.80 / 5.20 = 1.6923, so RSI = 100 − 100 / 2.6923 = 100 − 37.14 = 62.86 (rounded).
A single up-candle of 1.00 lifts RSI from 60 to about 62.86.
Because the formula is a ratio, RSI cannot leave the 0 to 100 range. If there are no losses at all, RSI is 100. If price is completely flat, the ratio is undefined, and the RSI node returns 50 for flat prices and for the first candle.
A shorter period makes RSI swing more widely and reach the extremes more often, while a longer one keeps it closer to 50. The period therefore changes what a threshold such as 70 means, so a threshold found with one period should not be copied to another without testing.
| RSI value | What it describes | Caution |
|---|---|---|
| Above 70 | Recent moves mostly upward | Can persist for many candles in a strong trend |
| Around 50 | Gains and losses about balanced | Says little about direction |
| Below 30 | Recent moves mostly downward | Can persist for many candles in a strong downtrend |
Overbought and oversold are not signals
A common rule of thumb calls RSI above 70 overbought and below 30 oversold. These are conventions, not laws. A high RSI only says that recent moves were mostly upward, and in a strong trend RSI can stay high for a long time while price keeps rising.
Because RSI is built from closes alone, it carries no information beyond price. It is often more useful as a filter or a measure of momentum inside a larger rule than as a standalone trigger.
In the graph editor
The RSI node has a single input socket, Close, an output socket RSI and a Period (N) setting. Connect Data.Close to it. To express a threshold, send the RSI output to a LessThan or GreaterThan node and compare it with a number constant, for example 30.
Key takeaways
- RSI = 100 − 100 / (1 + RS), where RS is the average gain divided by the average loss over N candles.
- With Wilder smoothing the averages update as (previous × (N − 1) + new) / N, and QuantRaider's
RSInode uses Wilder smoothing. - Readings above 70 or below 30 are rules of thumb, and a strong trend can keep RSI there for a long time.
- RSI is derived from closes only, so it is best treated as a measure of momentum rather than a standalone signal.