Placing a stop loss

Put the stop where the trade idea is wrong, not where the loss feels comfortable, and size from there.

All courses · Lesson 2 of 10 · Intermediate · 4 min

A stop loss is the price at which you accept that the trade idea was wrong. Where you put it decides how far price can move against you, and therefore how large your position can be.

Put the stop where the idea fails

A good stop has a reason: if price reaches it, the reason for the trade no longer holds. A stop placed at a fixed comfortable loss, with no link to the chart, is often either inside normal noise or arbitrarily far away.

Two common approaches are structure-based and volatility-based stops. Neither is better in general; they answer slightly different questions.

Structure-based stops

For a buy trade, one common approach is to place the stop just beyond the most recent swing low, so that the stop is hit only if the structure that supported the idea is broken. For a sell trade it sits just above a swing high. A small buffer beyond the swing point helps avoid being stopped by a wick that only touches the level.

Volatility-based stops

A volatility-based stop uses a multiple of the ATR (average true range), the typical distance price travels per candle. For example, a stop 2 × ATR below the entry adapts automatically: it is wider in turbulent markets and tighter in quiet ones. The ATR lesson explains how it is calculated.

Strengths

  • Structure stops have a visible reason on the chart, so it is clear when the idea has failed.
  • ATR stops scale with current volatility, so the same rule suits quiet and turbulent periods.

Weaknesses

  • A swing point can be far away, which forces a small position to keep the same risk.
  • An ATR multiple may land in the middle of a price zone with no structural meaning.
  • Both depend on choices (buffer size, ATR period, multiple) that should be tested rather than guessed.

Some traders combine the two, for example by using the swing point but rejecting the trade if the distance is larger than a chosen multiple of ATR. That keeps the stop meaningful while still avoiding trades whose required stop is unreasonably wide for the current market.

Size from the stop, never the stop from the size

The order of decisions matters. First find the stop where the idea is invalid, then compute the position size that makes the loss at that stop equal to your chosen risk. Moving the stop closer so that a larger position fits the same risk makes it more likely to be hit by ordinary movement.

Worked example

Structure-based stop and position size

  1. Account €20,000, risk 1% per trade, so the amount at risk is €200.
  2. Buy at 100.00. The last swing low is 97.50; add a buffer of 0.30, so the stop is at 97.20.
  3. Stop distance = 100.00 − 97.20 = 2.80 per unit.
  4. Position size = €200 / 2.80 = 71.43 units, rounded down to 71 units.
  5. Actual risk = 71 × 2.80 = €198.80.

A 71-unit position risks about 0.99% of the account if the stop is hit.

With the ATR approach the arithmetic is the same. If ATR is 1.20 and you use 2 × ATR, the distance is 2.40: a buy at 100.00 has its stop at 97.60, and €200 of risk gives 83.33, so 83 units.

Costs belong in this calculation too. The spread and any slippage mean a stop can fill slightly beyond the price you set, so the real loss may be a little larger than planned. Some traders add a small allowance to the stop distance for this, and the trading costs course shows how to express these costs as a fraction of your risk.

A final check is whether the trade is worth taking at all. If the sensible stop is so far away that the position becomes tiny, or the target is closer than the stop requires for a reasonable reward-to-risk, the right decision may simply be to skip the trade rather than force a different stop.

Key takeaways

  • Place the stop where the trade idea is shown to be wrong, not where the loss feels comfortable.
  • Structure-based stops use swing points; volatility-based stops use a multiple of ATR.
  • Position size = amount at risk / stop distance, so the stop comes first and the size follows.
  • Do not widen a stop after entry, because it invalidates the risk you sized for.

Sign in to save your progress and quiz results.